+8613912466955 Info@tzrfiltration.com
Vacuum Disc Filter Cake Cracking: Causes and Diagnostic Checks

Cracks in a vacuum disc filter cake can provide paths for air to bypass wetter parts of the solids. A cake may therefore look dry at the surface while still leaving the filter above its moisture target.

The first diagnostic question is when the cracks form. Cracking during dewatering, separation from the cloth, and normal breakage at discharge are different observations. Identifying the stage and location helps determine what to measure next.

Why does filter cake crack during dewatering?

A cake can shrink as liquid is removed and the particle structure changes. Uneven thickness, variable cake formation, and material properties can influence how that shrinkage develops. If openings create easier air paths, some airflow may pass through them rather than remove water uniformly from the cake.

Metso's guide to concentrate filtration discusses cake shrinkage and air bypass during drying. It also describes the tradeoff between drying time and capacity. The practical investigation below applies those principles to observations at a rotary disc filter; it is not a fixed recipe for every mineral.

Distinguish cracks from uncovered cloth

An open area on a sector may be a crack through previously formed cake, or it may be a place where cake never formed adequately. The corrective investigation differs.

Observe the same area as it leaves the slurry. If coverage is already incomplete, review formation and feed distribution before concluding that drying caused the opening. If the cake begins uniformly covered and opens later, shrinkage or detachment becomes more relevant.

Record whether the effect repeats at the same sector, at the same rotational position, or across most of the machine. Observations from designated viewing positions, photographs, and time-aligned operating records can help. Do not reach into operating equipment to inspect a crack.

Locate the symptom in the cycle

Where the opening first appearsWhat to investigate
As the sector leaves the slurryInitial cake coverage, feed distribution, and local sector condition
Later in the dewatering zoneShrinkage, thickness variation, and operating conditions
Along a repeated sector edgeLocal cloth fit, support, and attachment condition
Only as cake is dischargedWhether normal release is being mistaken for a drying defect

This pattern-based approach helps choose the next check. It does not establish a cause from appearance alone.

Confirm whether cracking affects the product

Measure cake moisture using an agreed method and sampling point. Compare the result with crack observations collected during the same operating period.

Where practical, investigate variation across the discharge stream as well as the average. A combined sample may hide uneven drying, while a deliberately selected wet lump may exaggerate the condition of the entire product.

Keep sample identification and process records connected. The wet-basis and dry-basis moisture guide explains reporting conventions that can otherwise confuse before-and-after comparisons.

If the required moisture and production remain stable, visible cake breakage may not be the plant's main performance constraint. Establish the impact before making changes.

Compare feed conditions before changing the filter

Review whether the symptom began after a change in ore blend, particle-size distribution, slurry concentration, temperature, or reagent practice. Preserve representative material from both satisfactory and difficult operation when possible.

Check the stability of feed delivery, not only its shift-average concentration. A short dilute period can create a different cake from the material produced a few minutes later.

The thickener underflow guide addresses feed stability. For this investigation, the key task is to align the feed change with the observed point at which cake behavior changes.

Do not adjust flotation chemistry solely to improve a filtration photograph. Any proposed reagent change should be assessed with the upstream process team and tested for its wider effects.

Separate machine-wide patterns from local defects

If most sectors show similar behavior after a feed change, the investigation should consider a common process influence. If one sector repeatedly differs from adjacent sectors under the same feed, inspect that location during an appropriate shutdown.

Review cloth fit, sector support, connections, and other relevant components using the machine documentation. Compare the findings with known good sectors.

A local component defect and a process change can occur together. Repairing an identified defect should be followed by a check of the remaining cake pattern, rather than assuming that every moisture issue has the same cause.

Run a controlled operating trial

Choose one justified change at a time within the approved operating range. Record the original condition, the change, stabilization period, cake appearance, production, moisture, and relevant vacuum measurements.

Disc speed changes affect more than drying time. They also change the time available for formation and the cake delivered to discharge. A slower speed may improve one result while reducing production or changing cake thickness.

Similarly, a higher vacuum reading does not prove that airflow is usefully distributed through the cake. Compare the product result and production together.

Repeat a promising trial to determine whether the result persists. Avoid comparing a good-feed trial with a difficult-feed baseline and attributing all improvement to the setting change.

Use laboratory testing to investigate persistent behavior

If acceptable operation cannot be established, test representative slurry under a controlled sequence. Record formation, dewatering, moisture, and the appearance of cracks or detachment.

Ask the laboratory to explain how the test conditions relate to the installed filter. A pressure-filtration test that compresses a cake demonstrates a different process from an open vacuum disc filter. Its outcome may inform technology selection, but it does not prove that an equivalent modification is available on the existing machine.

Use the sampling guide to preserve the feed conditions that matter. If the duty has changed beyond the equipment's capability, the retrofit or replacement guide provides a decision framework.

Information to send for technical review

Provide photographs or video showing where cracks first appear, the affected sectors, feed information, cake moisture records, throughput, disc speed, and vacuum measurement locations. Include recent maintenance or process changes.

Contact Tongzhiren Filtration with this evidence to discuss the filtration requirement and possible next checks. A synchronized set of observations is more useful than the statement “the cake is cracked.”

Frequently asked questions

Can cracked cake still be wet?

Yes. Cracks can carry air around wetter regions, so appearance alone does not establish final moisture.

Should vacuum always be increased when cake cracks?

No. Establish the cause and evaluate any approved change against moisture, throughput, and cake behavior together.

Are cracks at discharge necessarily a problem?

No. Cake may break as it is released. Distinguish that event from cracks developing during the drying part of the cycle.

What is the most useful first observation?

Identify when the opening first appears and whether it repeats locally or across the machine. Then connect that observation to measured performance.

Send us a Message

Captcha
Home
whatsapp
Email
Inquiry