+8613912466955 Info@tzrfiltration.com
Vacuum Disc Filter Cake Discharge Problems: Why Cake Sticks

When cake remains on a vacuum disc filter after the discharge zone, check whether the problem starts with cake formation, the cloth surface, or the release mechanism. A weak or uneven cake, a changed cloth condition, and an incorrectly functioning discharge system can produce similar symptoms. Identify where the material first fails to release before adjusting pressure or replacing parts.

This guide concerns cloth-covered vacuum disc filters. Ceramic disc filters and other filter types can use different release and cleaning arrangements, so their procedures should not be transferred without checking the equipment documentation.

What does a cake discharge problem look like?

Distinguish cake that stays attached to the cloth from cake that releases successfully and then accumulates in the chute. The first observation directs attention toward the filter cycle and release system; the second also requires a downstream handling review.

Watch several rotations from an approved viewing position. Record the sector identity, the extent of material remaining after discharge, and whether the same pattern repeats. A short video with a clear reference to rotation direction can make a support request much more useful.

Observed patternFirst comparison to make
One sector repeatedly retains cakeCompare its cloth, connections, and release behavior with adjacent sectors
Most sectors change after a feed disturbanceCompare cake formation and feed records before and after the disturbance
Trouble begins after re-clothingCheck the installed cloth specification, fit, and work records
Release becomes intermittent during busy plant periodsCompare discharge events with the local utility conditions
Cake leaves the cloth but builds up below itReview chute and conveyor conditions separately from cloth release

These observations select the next investigation; they do not establish a cause on their own.

Check the cake before checking the discharge setting

Observe the cake as it emerges from the slurry and again immediately before release. Is coverage complete? Does thickness vary across the sector? Is the material already breaking away before the intended discharge point?

Metso's concentrate filtration guide identifies minimum cake thickness for effective discharge as a practical limitation in vacuum filtration. There is no single thickness target that applies to every slurry and machine.

Compare a difficult operating period with a satisfactory period on the same filter. Record feed solids concentration, disc speed, slurry level, cake condition, and moisture using consistent methods. If the cake is poorly formed before it reaches discharge, changing the release mechanism alone may leave the underlying problem unresolved.

The thickener underflow stability guide explains the feed conditions to record when filtration changes unexpectedly.

Inspect the cloth as an installed component

A cloth specification is only part of the investigation. During an appropriately isolated inspection, check whether the cloth is fitted and secured according to the supplier's instructions, whether folds or damage are present, and whether deposits differ between affected and unaffected areas.

If the issue followed a cloth change, confirm the delivered material against the approved specification. Record the batch and installation date rather than relying on appearance alone. A different cloth may need a controlled trial even if its dimensions match.

Compare cake release alongside filtrate quality and production. A change that makes cake fall away more readily is not a successful solution if unacceptable solids losses appear in the filtrate. The filter cloth selection guide provides the wider evaluation framework.

Confirm how this machine releases cake

Consult the machine drawing and operating manual to identify its discharge sequence. Where compressed-air blowback is installed, establish which components deliver the pulse and how the sequence relates to sector position. Where mechanical discharge components are present, use their specified inspection and clearance procedure.

BOKELA's BoVac Disc description gives one manufacturer's example of compressed-air blowback through filter segments. It supports the operating principle; its design details and performance claims are not specifications for a Tongzhiren filter.

Have qualified personnel compare the actual operation with the approved sequence. A control command appearing on a screen does not by itself demonstrate that the corresponding valve and air path operated correctly.

Measure the air supply at a useful location

For a filter using blowback, a reading at the compressor house may not describe conditions at the filter during a discharge event. Ask the responsible technician to review the available local measurements, the pressure trend during demand, and the condition of the supply components identified in the equipment documentation.

Record whether other plant users were operating when the symptom occurred. A time-aligned record can help separate a recurring supply disturbance from a problem limited to one sector.

There is no universal blowback pressure or pulse duration. Do not increase either beyond the approved range to compensate for an unidentified fault. Inspecting moving components or opening pressurized connections requires the plant's isolation procedure.

Test one justified change at a time

Use a short trial record with the original setting, proposed change, feed condition, observation period, and results. Include retained cake, dry-solids production, cake moisture, and filtrate quality where measured.

For example, if an approved timing correction improves release, repeat the observation under comparable feed conditions before declaring the issue resolved. If the ore blend changed at the same time, preserve that fact in the report.

A useful result is consistent discharge with acceptable product quality and production. A visually clean sector during one rotation is insufficient evidence of stable operation.

Information to send for technical support

Provide the filter model, cloth specification, photographs or video of the affected sectors, recent feed and moisture records, and the maintenance history preceding the problem. For blowback systems, include the available local pressure records and relevant control observations.

Contact Tongzhiren Filtration with these details to discuss the installed filter and the next appropriate checks.

Frequently asked questions

Will more blowback air always remove sticky cake?

No. First establish whether the cake formed correctly and whether the release system works as designed. Use only the manufacturer's permitted settings.

Does cake sticking mean the cloth needs replacement?

Not necessarily. Compare cloth condition with feed changes, installation records, and the discharge sequence before deciding.

Why does only one sector retain cake?

A repeated local pattern makes that sector's cloth, connections, and release path useful inspection targets. The pattern is a clue, not proof of a specific defect.

What if cake releases but blocks the chute?

Review downstream handling and cake condition. Successful separation from the cloth does not establish that the chute and conveyor can handle the discharged material.

Send us a Message

Captcha
Home
whatsapp
Email
Inquiry